ELENDEBG
+30 2310 607032 · info@aineas.gr · пон–пет 09:00–17:00
Услуги Лабораторията Процесът Кодове за грешки Контакти thesolarportal.com thesolarlink. →
ELENDEBG

KACO

Ремонт на инвертори KACO — кои модели поемаме и как работим →

Най-честите грешки при инвертори Kaco

ПРИ МНОГО ИНВЕРТОРИ KACO ОКОЛО 100 000 KWH СЕ ПОЯВЯВАТ ГРЕШКИ, СВЪРЗАНИ С НЕПРАВИЛНАТА РАБОТА НА ВАШИЯ ИНВЕРТОР.
ОПИТАЙТЕ ДА ИЗКЛЮЧИТЕ ПРЕКЪСВАЧА НА МРЕЖАТА И ДА ГО ВКЛЮЧИТЕ ОТНОВО СЛЕД 2-3 МИНУТИ.
АКО ПРОБЛЕМЪТ ПРОДЪЛЖАВА, ТРЯБВА ДА НИ ИЗПРАТИТЕ ИНВЕРТОРА ЗА РЕМОНТ.

Най-честите грешки при инверторите Kaco

KACO

62 кода
ErrorПричинаДействие
FS 10ПрегряванеIn case of overheating, the inverter switches off. Possible causes: • Excessively high ambient temperature • Fan covered • Inverter defective.Подробно → FS 100ПрегряванеThe device has been switched off because the temperatures in the housing were too high. — Проверете температурата около инвертора и отстранете всичко, което го обгражда, за да я понижите, както указва съобщениетоПодробно → FS 101Грешка в измерванетоThe unit has shut down because of implausible internal measured values.Подробно → FS 102Грешка в измерванетоThe unit has shut down because of implausible internal measured values.Подробно → FS 103Грешка в измерванетоThe unit has shut down because of implausible internal measured values.Подробно → FS 104Грешка в измерванетоThe unit has shut down because of implausible internal measured values.Подробно → FS 105Грешка в измерванетоThe unit has shut down because of implausible internal measured values.Подробно → FS 106Грешка в измерванетоThe unit has shut down because of implausible internal measured values.Подробно → FS 17Грешка в мрежатаThe activated grid and system protection has been tripped.Подробно → FS 18Ток на утечкаResidual current was detected. The feed-in was interrupted.Подробно → FS 19Изолационно съпротивлениеThere is an insulation fault on the PV generator. The feed-in was interrupted.Подробно → FS 30Грешка в измерванетоThe current and voltage measurements in the inverter are not within acceptable range.Подробно → FS 32Мрежово релеThe internal grid separation relay test has failed.Подробно → FS 33Постоянен ток на изходаThe DC feed-in has exceeded the permitted value. This DC feed-in can be caused by grid conditions and may not necessarily indicate a fault.Подробно → FS 34КомуникацияA communication error has occurred in the internal data transmission.Подробно → FS 35Вътрешна грешкаProtective shutdown of the software (AC overvoltage, AC overcurrent, DC link overvoltage, DC overvoltage, DC overtemperature).Подробно → FS 36Вътрешна грешкаProtective shutdown of the hardware (AC overvoltage, AC overcurrent, DC link overvoltage).Подробно → FS 38DC пренапрежениеThe voltage of the DC generator is too high. The PV generator is configured incorrectly.Подробно → FS 40Понижено напрежение в мрежатаThe voltage of a grid phase is too low;Подробно → FS 41Прекъсната фазаthe grid cannot be fed into. The phase experiencing failure is displayed.Подробно → FS 42Прекъсната фазаthe grid cannot be fed into. The phase experiencing failure is displayed.Подробно → FS 43Прекъсната фазаthe grid cannot be fed into. The phase experiencing failure is displayed.Подробно → FS 44Прекъсната фазаthe grid cannot be fed into. The phase experiencing failure is displayed.Подробно → FS 45Прекъсната фазаthe grid cannot be fed into. The phase experiencing failure is displayed.Подробно → FS 46Прекъсната фазаthe grid cannot be fed into. The phase experiencing failure is displayed.Подробно → FS 47Грешка в мрежатаThe measured line-to-line voltage is outside of the tolerance limits.Подробно → FS 48Понижена честота на мрежатаGrid frequency is too low. This fault may be grid-related.Подробно → FS 49Повишена честота на мрежатаGrid frequency is too high. This fault may be grid-related.Подробно → FS 50Пренапрежение в мрежатаThe grid voltage measurement according to EN 50160 has exceeded the maximum permitted limit value. This fault may be grid-related.Подробно → FS 57СамопроверкаWaiting time of the inverter after a fault.Подробно → FS 58ПрегряванеThe temperature inside the unit was too high. The inverter switches off to prevent damage to the hardware.Подробно → FS 59СамопроверкаA fault occurred during a self-test.Подробно → FS 67Силова секцияThere is a fault in the power section.Подробно → FS 70ВентилаторThe fan is malfunctioning.Подробно → FS 73Грешка в мрежатаStandalone mode was detected. — Това съобщение е само информативноПодробно → FS 80Изолационно съпротивлениеThe insulation measurement cannot be performed because the generator voltage is too volatile. — Това съобщение е само информативноПодробно → FS 81Пренапрежение в мрежатаOvervoltage has been detected on a conductor. An internal protective mechanism has disconnected the device to protect it against damage.Подробно → FS 82Пренапрежение в мрежатаOvervoltage has been detected on a conductor. An internal protective mechanism has disconnected the device to protect it against damage.Подробно → FS 83Пренапрежение в мрежатаOvervoltage has been detected on a conductor. An internal protective mechanism has disconnected the device to protect it against damage.Подробно → FS 84Междинна верига (DC link)A voltage deviation has been found in the DC link. An internal protective mechanism has disconnected the device to protect it against damage.Подробно → FS 85Междинна верига (DC link)A voltage deviation has been found in the DC link. An internal protective mechanism has disconnected the device to protect it against damage.Подробно → FS 86Междинна верига (DC link)Overvoltage has been found in the DC link. An internal protective mechanism has disconnected the device to protect it against damage.Подробно → FS 87AC свръхтокA current that has been found on a conductor is too high. An internal protective mechanism has disconnected the device to protect it against damage.Подробно → FS 88AC свръхтокA current that has been found on a conductor is too high. An internal protective mechanism has disconnected the device to protect it against damage.Подробно → FS 89AC свръхтокA current that has been found on a conductor is too high. An internal protective mechanism has disconnected the device to protect it against damage.Подробно → FS 93Вътрешна грешкаThe control board is defective.Подробно → FS 94Вътрешна грешкаThe control board is defective.Подробно → FS 95Силова секцияThe power section is defective.Подробно → FS 96Силова секцияThe power section is defective.Подробно → FS 97AC свръхтокToo much power has been fed into the grid. Complete disconnection of the device.Подробно → FS 98Вътрешна грешкаAn internal protective mechanism has disconnected the device to protect it against damage. Complete disconnection of the device.Подробно → FS 99Вътрешна грешкаAn internal protective mechanism has disconnected the device to protect it against damage. Complete disconnection of the device.Подробно → OS 1СамопроверкаSelf-test: The grid parameters and generator voltage are being checked.Подробно → OS 11Ограничаване на мощносттаPower limitation: If the generator power is too high, the inverter limits itself to the maximum power (e.g. around noon if the generator capacity is too large).Подробно → OS 2Ниско DC напрежениеInsufficient generator voltage and power, status before the transition to night shutdownПодробно → OS 60Ниско DC напрежениеThe inverter does not begin feeding into the grid until the PV voltage falls below a specified value.Подробно → OS 61Дистанционно изключванеThe external limit Power control was activated by the grid operator. The inverter limits its power. — Това съобщение е само информативноПодробно → OS 63Ограничаване на мощносттаP(f)/frequency-dependent power reduction: Frequency-dependent power reduction will be activated when the BDEW (German Association of Energy and Water Industries) Medium Voltage Directive goes into effect. Power reduction starts at a frequency of 50.2 Hz. — Това съобщение е само информативноПодробно → OS 64Ограничаване на мощносттаOutput current limiting: The AC current is limited once the specified maximum value has been reached. — Това съобщение е само информативноПодробно → OS 74Дистанционно изключванеThe grid operator limits the feed-in power of the inverter. — Това съобщение е само информативноПодробно → OS 79Изолационно съпротивлениеPV generator’s insulation is being measured — Това съобщение е само информативноПодробно → OS 8СамопроверкаChecks the shutdown of the power electronics as well as the grid relay before feed-in mode.Подробно →

Ръководства KACO (PDF)